English
V-One Safety Information
1.0 Introduction
V-One is a precision tool for electronics prototyping. As with any such equipment, V-One and the accompanying materials and accessories should be handled with care. Please review the following material to ensure a safe work environment and to maintain optimal machine performance.
V-One is not only an excellent tool for the seasoned electrical engineer but it is also a great way to teach electronics. The V-One and drill are for use as-is. Any modifications or improper use without explicit approval and direction from Voltera may damage the machine, may cause bodily harm, and will void your warranty.
Never leave V-One unattended while in use and supervise young and inexperienced users to ensure safe operation. In case of emergency or prior to performing any maintenance, please ensure power cable is disconnected from V-One.
2.0 Markings and warning statements
All users of the machine must read this safety information carefully before using V-One. Improper use of V-One or use in a manner not specified by Voltera may result in impairment of protections and may present hazards such as electric shock, crushing injuries, or pinch points.
2.1 Mechanical hazards
V-One contains moving components that may cause pinch or crush injuries.
Keep hands and tools clear of the machine while it is operating.
Do not reach into the machine while motion is in progress.
Ensure all motion has stopped before interacting with the system.
2.2 Hot surfaces
The build surface may become hot during operation.
Do not touch the build surface while heated.
Allow sufficient time for cooling before handling.
Keep flammable materials away from heated areas.
2.3 Application-specific materials and chemicals
Materials, inks, and cleaning agents used with V-One may present chemical, fire, or health hazards.
Only use materials recommended by Voltera.
Review all applicable safety data sheets (SDS) before use.
Do not mix unknown or incompatible chemicals.
Ensure adequate ventilation when using inks or solvents.
Isopropyl alcohol and inks may be flammable. Keep away from ignition sources.
Material safety is the responsibility of the user.system.
2.4 Electrical connections
Improper electrical use may result in electric shock or fire.
Connect only to a properly earthed outlet.
Do not touch electrical contacts while the system is powered.
Keep liquids away from electrical components.
Inspect power cables regularly and discontinue use if damaged.
Disconnect power before cleaning or maintenance.
If a fuse requires replacement, contact Voltera Support at [email protected]. A blown fuse may indicate a serious fault.
2.5 Personal protective equipment
Wear eye protection when handling inks or cleaning agents.
Wear protective gloves when handling chemicals or solvents.
2.6 Lifting and handling
V-One is designed as a one-person lift.
Lift only from the base of the unit.
Use proper lifting technique.
Ensure a stable surface before placement.
2.7 Do not disassemble
V-One contains no user-serviceable parts.
Do not open or disassemble the device.
Unauthorized modification or repair may result in injury and will void the warranty.
Contact Voltera Support for service or repair.
3.0 Conformity
3.1 Product
Voltera V-One
3.2 Manufacturer
Voltera Inc. 180 Northfield Dr W, Suite 2 Waterloo, ON N2L 0C7 Canada
3.3 Declaration
Voltera Inc. declares under its sole responsibility that the product Voltera V-One complies with the directives 2014/35/EU and 2014/30/EU, as well as the harmonized standards and subsections IEC 61010-1:2010, IEC 61010-2-010:2019, IEC 61326-1:2021, and EN 55011 Class A. The full EU Declaration of Conformity can be presented upon request.
4.0 Disposal
At end of life, the Voltera V-One and its electronic components must be disposed of through an approved electronic-waste collection or recycling facility; do not dispose of the unit with household waste.
5.0 Specifications
Disclaimer: Voltera reserves the right to change or update the following specifications at any time without notice. Please contact [email protected] for the most up-to-date information.
Hardware
Metric
Imperial
Maximum dimensions
40 × 26 × 21 cm
16 × 11 × 9’’
Weight
7 kg
16 lb
Environmental conditions
Operating temperature
15-30°C
59-86°F
Maximum altitude
2000 m
1.24 miles
Relative humidity
80%
Pollution degree
2
Maximum temperature
240°C
464°F
Ramp rate
2°C/s
3.6°F/s
Power requirements
Voltage
100-120 ACC
200-240 ACC
Current
4.7 A 50/60 Hz
2.5 A 50/60 Hz
Power
0.6 A
Leakage current
0.5 mA
Power
221 W
Drill Safety Information
1.0 Introduction
The V-One drill attachment (the drill) is a precision tool for electronics prototyping, specifically intended as an add-on to extend the functionality of the Voltera V-One to allow drilling of holes in FR1 substrates. Please review the following documentation to ensure a safe work environment and maintain optimal machine performance.
2.0 Markings and warning statements
2.1 Mechanical hazards
The drill contains rotating components that can cause serious injury.
Keep hands, hair, clothing, and jewelry away from the drill spindle.
Do not touch the drill bit while it is rotating.
Only interact with the drill after the software indicates motion has stopped.
Ensure the drill bit has fully stopped before removal or adjustment.
2.2 Sharp tools
Drill bits are sharp and may cause cuts or puncture injuries.
Handle drill bits with care.
Store drill bits safely when not in use.
Wear appropriate protection when changing bits.
2.3 Dust and debris
Drilling operations may generate hazardous dust. Only drill materials approved by Voltera. Drilling unapproved materials may generate hazardous dust or fumes. Consult relevant safety data sheets (SDS) before use.
2.4 Electrical connections
Improper electrical use may result in electric shock or fire.
Use only the supplied power adapter.
Ensure the power adapter remains easily accessible during operation.
Disconnect power before servicing or cleaning.
Inspect cables regularly and discontinue use if damaged.
Keep liquids away from electrical components.
2.5 Personal protective equipment
Safety glasses are required during drilling operations.
Use a dust mask or respirator when drilling produces airborne debris.
Wear protective gloves when handling drill bits or debris.
2.6 Do not disassemble
The drill contains no user-serviceable parts.
Do not open or disassemble the drill assembly.
Unauthorized modification or repair may result in injury and will void the warranty.
Contact Voltera Support at [email protected] for service or repair.
3.0 Conformity
3.1 Product
Voltera V-One drill attachment
3.2 Manufacturer
Voltera Inc. 180 Northfield Dr W, Suite 2 Waterloo, ON N2L 0C7 Canada
3.3 Declaration
Voltera Inc. declares under its sole responsibility that the product Voltera V-One drill attachment complies with the directives 2014/35/ EU and 2014/30/EU, as well as the harmonized standards and subsections IEC 61010-1:2010, IEC 61010-2-010:2019, IEC 61326-1:2021, and EN 55011 Class A. The full EU Declaration of Conformity can be presented upon request.
4.0 Disposal
At end of life, the Voltera V-One drill attachment and its electronic components must be disposed of through an approved electronic-waste collection or recycling facility; do not dispose of the unit with household waste.
5.0 Specifications
Disclaimer: Voltera reserves the right to change or update the following specifications at any time without notice. Please contact [email protected] for the most up-to-date information.
Environmental conditions
Operating temperature
15-30°C
59-86°F
Maximum altitude
2000 m
1.24 miles
Relative humidity
80%
Pollution degree
2
Power requirements
100-240 ACC, 50/60 Hz
25 W DC, 12 V, 2.08 A
Other equipment
A V-One is required to operate the drill.
Last updated
Was this helpful?